West-control-solutions 9500 Manuel d'utilisateur

Users ManualCAL ControlsCAL 9500PProgrammableProcess ControllerEnglish Français Deutsch Italiano Español

LEVEL AFunction Options[Factory settings] shown in bracketsLinear Input ScalingPlease read in conjunction with Linear Input Set-up Procedure on

11PROGRAMMERINDEXFunction overview 11Getting started 12Program run mode 12Display functions 12Example program 13Function map 14Function list 16Memory

12GETTING STARTED (PROGRAMMER)For users with previous experience of configuring programmers, the

13TYPESPRSPRR105T.SP137TYPESOAKSINT45TYPESTEPT.SP85TYPESPRSPRR55T.SP30TYPELOOPPCYC1TYPESPRSPRR105T.SP137TYPESOAKSINT45TYPESTEPT.SP85TYPESPRSEG1SEG2SEG

14PROGRAMMER FUNCTION MAPTUNEOFFSTART HEREPress and hold▼ ▲for 3 secondsENTERPROGRAMLEVL1LEVLP▼▼✱▲LEVLALEVLCIf COMMS optionfitted, LEVEL Cappears betw

15E.OP2DE.OP2EE.OP3DE.OP3EE.OP2D3DE.OP2E3DE.OP2E3EE.OP2D3EE.OPNONE▲✱TYPESOAKTYPESTEPTYPELOOPTYPECALLTYPEE,OPEDITDELEDITINSTYPESPR▲✱Insert newsegment i

16Function Sub-functions Settings[Factory settings] shown in bracketsPress ▲ or ▼ to change Press ✱ ▲ or ✱ ▼ to changeTyPEDefine segment typeSPr

17Function Settings[Factory settings] shown in bracketsPress ▲ or ▼ to change Press ✱ ▲ or ✱ ▼ to changeE.oPEvent output[nonE]Function can be ap

18PROGRAMMING EXAMPLESPROG1RUNOFFEDITCOPYPROG1RUNOFFADDPROG(next)3 secs✱EDITPSTE3 secsSURENOSUREYESPROG2Program 1now pastedas Program 2✱3 secs✱SEG1SEG

19MECHANICAL INSTALLATIONThe Controller is designed to be sleeve mounted in a 1/16 DIN panel cutout with only thefront panel rated to NEMA4/IP66, prov

INDEX INSTRUMENT PANEL FEATURESINSTRUMENT PANEL FEATURES 2FUNCTIONS MENU 3GETTING STARTED 4Initial Set-up 4AUTOTUNE 4Tune or tune at setpoint program

EN61010 - /CSA 22.2 No 1010.1 92Compliance shall not be impaired when fitted to the final installation.Designed to offer a minimum of Basic Insulation

21INPUT OPTIONS123456 78LNInput(–)(+)ThermocoupleSupplySpare(+)123456 78LNInput(–)(+)Wire linkSupplySpare(+)RTD/PT100 2 wire123456 78LNInput(–)(+)Supp

INPUT SENSOR SELECTIONTemperature sensorsThermocouples Description Sensor range LinearitytC b Pt-30%Rh/Pt-6%Rh 0 to 1800 °C 2.0 *tC E Chromel/Con 0 t

SAFETY AND WARRANTY INFORMATIONINSTALLATIONDesigned for use:UL873 - only in products where the acceptability is determined by Underwriters Laboratorie

CAL ControlsCAL Controls LtdBury Mead Road, Hitchin, Herts, SG5 1RT. UKTel: + 44 (0)1462-436161 Fax: + 44 (0)1462-451801email: [email protected]

SINT PCYC SUB.PCall sub-program number nonE; 1 to number of programsSoak time interval Cont; 0.1 to 1400 (10) minProgra

Press and hold ✱ and use the ▲ or ▼ buttons to select from the choices Rly,SSd orAnLGdepending on the model supplied. SP2 and SP3 outputs will be auto

AUTOTUNE (continued)TUNE OR TUNE AT SETPOINT PROGRAMEnter program (▲▼) and from the displaytunE : oFF press and hold ✱ and press ▲ todisplay tunE :

SP2 / SP3 OUTPUT AND LED STATUS IN ALARM CONDITIONSP2 / SP3 ALARM ANNUNCIATORIf a Primary Alarm mode has been configured, when an alarm condition occu

7FUNCTION LIST (LEVELS 1 to 4 and A)Note: A Functions Menu is shown on page 3.LEVEL 1Function Options[Factory settings] shown in bracketsSELECT

8INPUT SELECTION AND RANGINGdI.SP [1] 0.1Select display resolution: for display of process value, setpoint,OFSt, Set.2, hi.SC, LoSC.hi.SC [sensor

9Function Options[Factory settings] shown in bracketsrEu.d Select output modes: Direct/ReverseCaution: Settings affect fail safe state.SP1 SP2[